SYF3L (3MP HDR 30fps)
Overview
SYF3L is a monocular camera with a 196° horizontal field of view. It combines a Sony ISX031 sensor with a built-in ISP and a MAX96717F serializer to deliver uncompressed 8-bit YUV422 at 1920(H) × 1536(V) and 30fps over GMSL2. It supports HDR, LED flicker mitigation (LFM), external triggering, and multi-camera synchronization.
Specifications
| Parameter | Value |
|---|---|
| Sensor | Sony ISX031, 2.95MP RGGB, 1/2.42-inch CMOS |
| Pixel size | 3.0 × 3.0µm |
| Output resolution and frame rate | 1920(H) × 1536(V) @ 30fps |
| Output format | Uncompressed YUV422, 8bit |
| ISP | Built-in |
| HDR / LFM | Supported |
| Optical resolution | Center ≥800 LW/PH |
| Serializer and link | MAX96717F, GMSL2 at 3Gbps |
| Power supply | 9–16V PoC, <200mA at 12V DC |
| Connector | Amphenol Fakra Z code |
| Operating temperature | −40 to +85°C |
| Enclosure protection | IP67 |
| Footprint / weight | 25 × 25mm / <50g |
Note The optical resolution specification applies to the image center.
Lens and Mechanical Dimensions
| HFOV / VFOV | F-number | EFL | Focus distance | Depth of field | Max. optical distortion | Lens protection / assembly |
|---|---|---|---|---|---|---|
| 196° / 154° | 2.0 | 1.51mm | 0.4m | 0.13m to infinity | −155% | IP67 / active alignment (AA) |
Hardware and Integration
| Component | I2C address (8bit) |
|---|---|
| Serializer | 0x80 |
| Sensor/ISP | 0x34 |
| Function | Setting |
|---|---|
| Frame synchronization | MAX96717F MFP7 |
| Sensor reset | MAX96717F MFP0 |
| Sensor error signal | MAX96717F MFP5 |
The built-in ISP outputs YUV. Configure the host SerDes for a 3Gbps GMSL2 link and an 8-bit YUV422 stream.
Camera Usage
NVIDIA Jetson Integration
SYF3L uses GMSL2 at 3Gbps and outputs 1920(H) × 1536(V) @ 30fps in YUV422 (UYVY). Select the package for your board, JetPack version and capture interface.
| Jetson platform | Adapter / carrier board | JetPack | Interface | Driver and installation guide |
|---|---|---|---|---|
| Jetson AGX Orin | SG8A-AGON-G2Y-A1 | 6.2 | V4L2 | Driver package · Installation guide |
| Jetson AGX Orin | SG8A-AGON-G2Y-A1 | 6.2.1 | V4L2 | Driver package · Installation guide |
| Jetson AGX Orin | SG8A-AGON-G2Y-A1 | 7.2 | V4L2 | Driver package · Installation guide |
| Jetson AGX Orin | SG8A-AGON-G2Y-A1 | 7.2 | SIPL | Driver package · Installation guide |
| Jetson AGX Orin | SG10A-AGON-G2M-A4 | 7.2 | V4L2 | Driver package · Installation guide |
| Jetson AGX Thor | TRD1 G2A | 7.2 | SIPL | Driver package · Installation guide |
- Connect the camera to the GMSL2 port specified in the package guide and check the power and port mapping.
- For V4L2, configure the device tree and capture port using the matching installation guide.
- SG8A-AGON-G2Y-A1, JetPack 6.2 / 7.2 — Enable 3Gbps on the connected port and follow the linked installation guide to select the camera profile in
raw_yuv_quick_bring_up.sh. - SG8A-AGON-G2Y-A1, JetPack 6.2.1 — Select
sgx-yuv-gmsl2in the overlay tool. Incamera_config.sh, enable 3Gbps and set sensor mode 1 for the connected port. - SG10A-AGON-G2M-A4, JetPack 7.2 — Set
sensor_mode=2andgmsl_mode=1for the connected port.
- SG8A-AGON-G2Y-A1, JetPack 6.2 / 7.2 — Enable 3Gbps on the connected port and follow the linked installation guide to select the camera profile in
- SIPL. Follow the SGX-YUV-GMSL2 guide for your platform. Select
SGX_YUV_GMSL2_3M_3G, configure the connected port and runnvsipl_camera. AGX Orin configuration · AGX Thor configuration - Use the package's capture example to verify output at 1920(H) × 1536(V) @ 30fps.
Integration with Custom Platforms
Use a deserializer that supports GMSL2 at 3Gbps. Configure PoC, the SerDes link and I2C mapping according to the block diagram. Set the host CSI receiver to 1920(H) × 1536(V) @ 30fps and 8-bit YUV422. For external frame synchronization, configure MAX96717F MFP7 as shown in the hardware table.
Note If you use a PANDA PG2 single-camera USB converter (Windows) or a CoaxCapture II CCG3-4H/8H capture card, verify model compatibility, link rate and driver requirements for your device.